CA: Chassis, Suspension & Steering Upgrades

Click to Enlarge

rubber protective “boots”
Click to Enlarge

Adjustable end link for many BMW front Anti-Roll bars.
Ground Control exclusive machined billet stainless steel tapered adapters press fit into stock holes. Adjustable length 6061 anodized rod, with wrench flats and jam nuts. 3 piece Aurora rod ends. Fits E30 M3, E36 M3, M coupe/Roadster and E46M3.

PLEASE NOTE Does not fit regular e30 or e36.

*(rubber protective “boots” available as an option)*

Fitting Time: 1.00 hour.

Product Code: gcadjtier

Click to Enlarge

Exclusive racing tie rod ends allow the bumpsteer to be adjusted, by moving the tie rods up and down with spacers.This is similar to the pieces used by BMW factory teams in Europe, and they recommend that the rod ends be inspected every session, and replaced if necessary.

Comes with Aurora aircraft grade rod ends and all spacers.

PLEASE SPECIFY EXACT MODEL WHEN ORDERING

Estimated Product Shipping Weight inc Packaging: 5.00 Kg

Product Code: gchybfmnt

For street and race use ...
HYBRID Camber / Caster Plates, a special version of Ground Control's race plates, toned down for dual-purpose cars. Uses a proprietary upper perch with a rubber insulator.

More camber adjustment than stock, caster adjustment, aircraft bearings, engraved with calibrated degrees, with stainless steel reinforcement. Every component is anodized or plated, including fasteners. Adds extra travel to avoid excessive bottoming out, this is a very well engineered product. The stainless steel reinforcement prevents electrolysis between the steel fender and the aluminum camber plate.

Camber and caster are separately adjustable by sliding the mounts, without removing any components from the car. The priority of this design is to allow fast, repeatable alignment changes at the track.

The Ground Control camber plates feature two sets of bearings, a proprietary bearing, made to our specs by Aurora in the USA, which allows for articulation of the shock shaft. This spherical bearing is very understressed, as the Ground Control design does NOT support the weight of the car on the spherical bearing. Instead, the weight of the car is supported by a completely separate articulating needle bearing, which is also manufactured for Ground Control in the USA.

*Please specify exact vehicle when ordering.

Estimated Product Shipping Weight inc Packaging: 6.00 Kg

Product Code: gc36fcammnt

Click to Enlarge

A work of art, carved from a single piece of billet aluminum. That is one way to describe the new street camber plate from Ground Control.

Fits entirely within the stock reinforcements, and is adjustable through a range of 0.5 to -2.6, and can be reversed for zero camber like the stock 96-99 M3. No bearings, and is rebuildable unlike the stock parts.

Available for E36 inc M3.
SPECIFY EXACT VEHICLE MODEL WHEN ORDERING.

Estimated Product Shipping Weight inc Packaging: 5.00 Kg

Product Code: gcfcarmbrng

Click to Enlarge

E30 M3 geometry, use ONLY with e30, e30 M3, or 92-95 e36 control arms. For 96-99 M3, use "m3bearing96" ( please enquire).

Priced as a pair

PLEASE SPECIFY YOUR EXACT VEHICLE MODEL WHEN ORDERING.

Estimated Product Shipping Weight inc Packaging: 10.00 Kg

Product Code: acsukp-7

Click to Enlarge

We can now offer Genuine AC SCHNITZER parts.

We have been appointed OFFICIAL UK DEALERS by AC SCHNITZER UK.

We offer all products from all the ranges including: styling / chassis / wheels etc…

Please see our ACS on line price and image list HERE,

We offer minimum 5% discount from the listed prices. Select “picture view” option at the top to see product images. Note the product page has it’s own “internal” vertical scroll bar.

Estimated Product Shipping Weight inc Packaging: 5.00 Kg

Click to Enlarge

Ground control Street version camber mounts.

The street version is the only version to be used with street springs, and is designed with features that harmonize with more conservative springs.

*(Please see varients section for models available)*

Estimated Product Shipping Weight inc Packaging: 10.00 Kg

Product Code: gcrcersm

Click to Enlarge

Rear shock mount to fit BMW, only recommended for race cars.

Complete with shock stem adapters.Uses a spherical bearing instead of urethane or rubber. Please specify 10, 12, 14 or 16mm stem diameter.

Billet aluminum with spherical bearings.

Note that ALL Ground Control rear shock mounts are clamped to the body for extra strength. Price per pair.

Estimated Product Shipping Weight inc Packaging: 3.00 Kg

REAR CAMBER ARMS
Click to Enlarge

FRONT CAMBER TOP MOUNTS
Click to Enlarge

Lowering the suspension on your car will also alter it's chassis geometry ( camber , castor, toe etc ) , so it is imperative to reset the full range of geometry settings following such installations to achieve the best possible chassis feel , handling , roadholding and tyre wear patterns .
Quite often an aftermarket lowering or coilover kit will take the geometry beyond the possible range of adjustment using the factory suspension components and mounts ; in these cases you must fit a good set of aftremarket alignment correction hardware .
Below are listed our recommended range of options for such products.

As an approximate guide for BMW cars, lowering the factory ride height by 50 mm will alter the Front Camber by 1.50 degrees and Rear Camber by 1.0 degrees . A 75 mm drop will alter by 2.50 degrees front and 2.00 rear .

These SPC kits offer increased front and rear camber adjustment , allowing you set your suspension to the exact required parameters.

Available for :

- E30 3 SERIES ( INC. M3)
- E36 3 SERIES ( INC. M3)
- E46 3 SERIES ( INC. M3)
- E85 Z4 INC ZM4
- E39 INC M5

Simple to install and hard wearing.

PLEASE REFER TO VARIATIONS SECTION FOR YOUR MODEL.

Eibach Price & Application List (Excel Format)

Product Code: tmse36fcbk

Click to Enlarge

Whether you need a positive camber change and don’t have adjustable camber
plates or you are looking for more adjustment with your camber plates, you
can change your camber by shimming the strut and spindle with the TMS bolt
kit. There are some things to take into account with this kit so please read the
installation tips below. An alignment is strongly recommended after installing
this part.

Applications: 1992-1999 E36 and 1994-2002 Z3

Parts list for kit:
• 4 12mm bolts
• 12 12mm washers

When would it be a good time to perform this work on my car?

The next time you are doing alignment or a track set up.
Installation Tips:

1. There are three washers per bolt. One washer must stay on the outside of the
strut. The other two washers can be put between the strut and spindle for more
camber if needed. If only one or no washers are needed, the extra washers
should also be put on the outside.

2. You will also need to check the clearance from the wheel and tire to the strut.
When you install washers between the strut and spindle, this tilts the wheel and
tire towards the strut. You will need at lest 5mm clearance or the tire will rub the
strut or spring perch.

3. If you need more wheel to strut clearance wheel spacers will solve the problem
as long as you have enough wheel to fender clearance. Turner Motorsport has
widths of spacers from 5mm to 30mm available for this car.

Estimated Product Shipping Weight inc Packaging: 5.00 Kg

Product Code: vmadjdl

Click to Enlarge

Probably the most overlooked suspension component in the performance world is the sway bar / anti roll bar end-link.
This simple component attaches the sway bar to each end of the suspension so the sway bar can do its job; promoting flat cornering of the vehicle in a turn.
This simple component can drastically hurt your car's performance if not optimized, especially in a BMW where high sway bar rates [and therefore high stresses] are common.

A sway bar with fixed length links can induce a load into any two cross-corners of your vehicle. The ability to neutralize the sway bar in your suspension system is a great advantage to baseline, balance, and refines your vehicle's handling characteristics. These links have achieved this by creating adapters that integrate current sway bar link technology to the traditional sway bar architecture. A worth while upgrade for any modified BMW.

Common issues with incorrect type or set up of drop links :

-Have you ever had a sway bar link bend..?
-Do you know if you are having suspension bind due to insufficient sway bar end link articulation (or simply poor design, bad bushing, etc)..?
-Have you ever had a sway-bar link fail at the welded joint between the ball and the link..?
-Do you want to properly corner weight your car..?

All these common issues that your vehicle may have had are addressed with this set.

These sway bar end links are the best solution, and unlike many others on the market these INCLUDE WEATHERPROOF "BOOTS" to help prevent the early demise of "open" type of drop link joints through corrosion / clogging .

Eliminate sway bar pre-load that adversely affects handling, strengthen your suspension, and truly optimize your setup with this strong Adjustable Sway Bar Link Set!... With no penalty, these links are quiet, just like OE links.

Put Simply: no matter at what ride height, stock or otherwise, OEM sway bar links are a weak link (literally) and add preload to your suspension. These adjustable links are superior to all other designs and unlike the upgraded units that may have come in your aftermarket sway bar kit, these have no polyurethane to squeak, tear, or blow out on the track.
These links feature a THK ball socket that is pre-lubricated, and sealed for durability and prolonged life. THK is an OE manufacturer for Porsche, Nissan, Honda, Ford, GM, Toyota and even BMW.

Ford In developing the new OEM suspension for their 2010 GT500, found these links made such a difference the factory test drivers believed the prototype sway bars had been re designed and they became OE equipment of this model. Thats an improvement!

The Benefits of This Design Over the OEM Sway Bar Links are:
•Heavy Duty Ball Socket Joint has excellent strength and life, never require servicing
•Large Diameter Link Rod to Resist Bending
•Designed for he needs of Racing and track use, and a Perfect Upgrade/ Replacement for Street Use!
•No Welded Joint to Fail
•Adjustable Design to Enable Corner Weighing and Swaybar Pre-load Adjustment and Yet Still Meet Racing Class Requirements
•High Mis-Alignment Design to Prevent Suspension Coil Bind (even better than spherical joints!)
•Joints are pre-greased and have a water-tight seal.
•Precision joint allows smooth operation.

WHEN ORDERING PLEASE SELECT REQUIRED PRIMARY LENGTH OF LINKS REQUIRED, 60,75, 85 OR 90 MM (See below to help you choose)
Tech Tip:
Measurements below are at stock ride height.
Longer or shorter length may vary accordingly to your ride height, geometry, clearance issues under the chassis around intercoolers/ oil coolers, body components, etc.
A good start is to order a longer length if your car is more than 1.5" lower than stock Here are some stock lengths, the Powergrid pieces are adjustable to fit the closest size application:

•E30 (M3), E24, E28, E34: front 60mm
•E36 M3: Front 60mm
•E39: Front 60mm (Stock Height. We recommend using 75mm if Lowered)
•E46 M3: Front 75mm
•E90: Front 60mm
•E60: Front 90mm

Note:
-End links do not fit non-M3 E36 (except 325i/is produced before 06/1992)
-Does not fit E30 rear, call or email for our kit for the E30 rear.

Estimated Product Shipping Weight inc Packaging: 2.00 Kg